AMIAD WORLDWIDE

Select your country and language

Based on your current location, we recommend this Amiad website for you

North America - English arrow
arrow down

How to Protect Your Irrigation System From Emitter Clogging

Mark Jolles<br>Former Director of Irrigation Sales
Mark Jolles
Former Director of Irrigation Sales // 06 Aug. 2017
sprinklers

(Last modified on October 12th, 2022)

In our last blog post, we discussed the main causes of emitter clogging of irrigation systems: physical, biological and chemical.

We also presented information on the types of emitter clogging expected from the use of different irrigation water sources.

Emitter clogging can cause a lot of damage to your agricultural irrigation system and significantly impact your bottom line. For this reason, a well-designed irrigation system should include preventative measures to avoid emitter clogging.

In this blog post, we will review what steps you can take to protect  against the clogging of your irrigation system.

What are the main causes of emitter clogging in irrigation systems?

Physical causes:

The most common physical causes of emitter clogging are sand particles and suspended solids that are too large to pass through the emitter openings.

In general, silt and clay particles do not cause clogging, unless they cluster together (flocculate) to form larger masses.

Biological causes:

Algae cells and bacteria alone are too small to clog emitters, but irrigation systems provide a good environment for the formation of biological aggregates. Bacterial slime can lead directly to emitter clogging of irrigation systems, and it can also cause physical particles to adhere to one another and form aggregates large enough to clog emitters.

When water with high biological activity is used for irrigation, emitter clogging due to algae and bacteria is common.  Surface water can also contain larger biological organisms that can clog emitters.

Chemical causes:

Mineral precipitation from water sources with high mineral content (hard water) can produce suspended solids and occurs when mineral solubility is low and when water temperature, pH level, redox potential and mineral concentration in the water are favorable.
These suspended solids will cause emitter clogging, with calcium carbonate being the most common precipitate.

Adding fertilizers can also be a cause of the clogging of the irrigation system, as the chemical interactions between the fertilizer and hard water may increase the prevalence of mineral precipitation.

How to protect against clogging of your irrigation system  

Water quality analysis

Prior to designing an agricultural irrigation system, it’s important to understand the quality of the irrigation water source by sampling the water and performing a water quality analysis. This analysis can be done at a water testing laboratory and the test protocol should be specific to irrigation water so that the results include typical contaminants that can cause the clogging of irrigation systems.

For example, the water analysis should include testing for hardness or mineral content [presence of calcium (Ca) and magnesium (Mg)], as mineral precipitation from water sources with high mineral content can produce suspended solids that clog emitters. Water quality testing can also provide information on total suspended solids (TSS) and particle size distribution, which will enable you to evaluate the expected quantity and size of organic and inorganic solids in the water that could potentially cause emitter clogging.

Clogging prevention solutions

When selecting clogging prevention solutions for your irrigation system, you should consider the following factors:

  • Operating conditions
  • Water source and quality
  • Clogging factors in the water
  • Emitter characteristics, such as the opening size

As these factors vary greatly from site to site, there is no standard recommendation to cover all conditions. In general, irrigation system design aimed at preventing emitter clogging should include the following:

  • Filtration
  • Chemical treatment (chlorination and/or acid injection)
  • Flushing allowances for irrigation lines

Filtration

A well-designed filtration system can prevent the physical clogging of irrigation system emitters. The size and type of agricultural irrigation filter is determined by the quality of the irrigation water, the maximum particle size that can be passed through the emitter opening and the volume of irrigation water that can flow through the filter before the filter needs to be cleaned.

You can usually get information about the maximum allowable particle size from the emitter manufacturer. If this information isn’t available, use a conservative rule of thumb that any particle larger than one-tenth the diameter of the smallest opening of the emitter should be removed. This also prevents bridging, which occurs when small particles aggregate and clog an emitter by forming a bridge across the opening.

If the water contains a large amount of sand, a sand separator can be installed to separate sand and other heavy particles from the water using centrifugal action. In addition, if the water source contains a large amount of silt, or is a fast-moving stream, a settling basin can be used to remove the solids.

Screen, media or disc filter solutions can be used to remove inorganic or organic clogging hazards such as slimes, algae, moss, snail and/or plant residues from irrigation water.

These agricultural irrigation filter solutions can either be manual, requiring an operator to manually remove the filter element(s) and wash or replace them, or automatically self-cleaning.

Chemical Treatment

Chlorination and disinfection procedures are key to controlling the biological clogging of irrigation systems. However, if the pH of the water is high (above 7.5), chlorination becomes relatively ineffective for bacterial control. For this reason, acid injection may be required to lower the pH level and increase the biocidal action of the chlorine.

Injecting acids, such as sulfuric, hydrochloric or phosphoric acid, into irrigation water to reduce pH levels will also decrease the possibility of mineral precipitation in hard water which also helps prevent emitter clogging of irrigation systems.

Naturally occurring dissolved iron in irrigation source water can be oxidized by aeration during pumping or chemically oxidized by acid injection to form precipitates that then clog emitters. If an irrigation water source is found to contain high levels of iron, treatment will be required. One solution is to pump the water to a tank or reservoir and aerate the water or add a chemical oxidant (such as chlorine) so that the ferrous iron is oxidized and can be settled or filtered out of the water before delivery to the irrigation system.

Note that acid and chlorine injection points should be at least 2 to 3 feet apart and should never be combined in the same container as dangerous chlorine gas is released.

When adding fertilizers to source water (fertigation), it is recommended that you perform tests to determine if the specific combination of fertilizers and other chemicals in the irrigation water interact and result in mineral precipitation that could cause emitter clogging.

Flushing

Regular flushing of irrigation systems is recommended to minimize the buildup of sediment and organic residues. The irrigation system should be designed so that the sizes of the main line, laterals and valves facilitate sufficient flushing velocity.

By including a regular maintenance program that includes inspection and flushing of your irrigation system, you will be able to significantly reduce the amount of emitter clogging occurring.

Proactively prevent the clogging of irrigation emitters

Defining a proactive approach to prevent emitter clogging of irrigation systems is essential to protecting your investment and ensuring that your crops get the water they need to thrive.

We have outlined the causes of emitter clogging and the steps that should be taken to prevent it.  

Click below to get guidelines with the measures you can take to safeguard your irrigation system.

Download the PDF

FAQs

Why is preventing clogging of emitters so important?

Emitter clogging can severely impair the performance of your irrigation system and significantly impact your production quality and quantity.

What types of irrigation methods are prone to clogging?

Any irrigation method that utilizes emitters is prone to clogging, such as drippers, sprinklers and micro-sprinklers.  

What are the common causes of emitter clogging?

The water source you are using to irrigate your crops directly influences the probability of emitter clogging. There are three main categories of emitter clogging: physical, biological and chemical.

 

Want to learn more about how to protect your irrigation system?

download icon
Ginosar Case Study